Nortel-networks Mediant TP-1610 SIP Uživatelský manuál Strana 55
- Strana / 280
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Mediant 2000 SIP User’s Manual 5. Web Management
Version 4.4 55 July 2005
5.8.5 Configuring the Profile Definitions
Utilizing the Profiles feature, the Mediant 2000 provides high-level adaptation when connected to
a variety of equipment (from both Tel and IP sides) and protocols, each of which require a
different system behavior. Using Profiles, users can assign different Profiles (behavior) on a per-
call basis, using the Tel to IP and IP to Trunk Group Routing tables, or associate different Profiles
to the gateway’s B-channels(s). The Profiles contain parameters such as Coders, T.38 Relay,
Voice and DTMF Gains, Silence Suppression, Echo Canceler, RTP DiffServ and more. The
Profiles feature allows users to tune these parameters or turn them on or off, per source or
destination routing and/or the specific gateway or its ports. For example, specific E1/T! spans can
be designated for to have a profile which always uses G.711.
Each call can be associated with one or two Profiles, Tel Profile and (or) IP Profile. If both IP and
Tel profiles apply to the same call, the coders and other common parameters of the preferred
Profile (determined by the Preference option) are applied to that call. If the Preference of the Tel
and IP Profiles is identical, the Tel Profile parameters are applied.
Note: The default values of the parameters in the Tel and IP Profiles are identical to
the Web/ini file parameter values. If a value of a parameter is changed in the
Web/ini file, it is automatically updated in the Profiles correspondingly. After
any parameter in the Profile is modified by the user, modifications to
parameters in the Web/ini file no longer impact that Profile.
5.8.5.1 Coder Group Settings
Use the Coders Group Settings screen to define up to four different coder groups. These coder
groups are used in the Tel and IP Profile Settings screens to assign different coders to Profiles.
To configure the coder group settings, take these 8 steps:
1. Open the ‘Coder Group Settings’ screen (Protocol Management menu > Profile
Definitions submenu > Coder Group Settings option); the ‘Coder Group Settings’ screen is
displayed.
Figure
5-9: Coder Group Settings Screen
2. In the ‘Coder Group ID’ drop-down list, select the coder group you want to edit (up to four
coder groups can be configured).
3. From the coder drop-down list, select the coder you want to use. For the full list of available
coders and their corresponding ptimes, refer to the ini file parameter ‘CoderName_ID’
(described in Table
6-3).
Note: Each coder can appear only once.
4. From the drop-down list to the right of the coder list, select the size of the Voice Packet
(ptime) used with this coder in milliseconds. Selecting the size of the packet determines how
many coder payloads are combined into one RTP (voice) packet.
Note 1: The ptime packetization period depends on the selected coder name.
- User’s Manual 1
- Table of Contents 3
- List of Figures 8
- Mediant 2000 SIP 10
- List of Tables 10
- Trademarks 12
- Customer Support 12
- Related Documentation 12
- 1 Overview 13
- 1.1 Available Configurations 14
- 1.2 SIP Overview 15
- 1.3 Mediant 2000 Features 15
- 1.3.4 Supported SIP Features 16
- 2.1 General 19
- 2.3 The TP-1610 Board 20
- 2.3.1 Board Hot-Swap Support 21
- 2.3.1 on page 21 23
- 2.4 Rear Transition Module 24
- 2.5 Optional CPU Board 25
- 3.1 Unpacking 27
- 3.2 Package Contents 27
- Electrical Earthing 31
- RJ-48c Connector and Pinout 32
- 1 2 3 4 5 6 7 8 33
- 4 Getting Started 35
- 5 Web Management 39
- 5.4 Password Control 40
- 5.7.1 Main Menu Bar 42
- 5.7.2 Saving Changes 43
- 5.8 Protocol Management 44
- 5.8.2 Advanced Parameters 45
- 8.6 on page 146 49
- 5.8.4.4 on page 54 49
- 5.8.4.3 Internal DNS Table 53
- 5.12 on page 53
- 5-5: Trunk Group Table 59
- 5-6: Channel Select Modes 61
- 5.9 Advanced Configuration 62
- 5.8.5 on page 55) 65
- 5.9.6 Regional Settings 70
- 5.10.1 Gateway Statistics 71
- • DNS Disable 73
- • DNS Resolved 73
- • DNS Unresolved 73
- 5.10.4 System Information 77
- 5.11 Software Update Menu 78
- 5.11.2 Auxiliary Files 82
- 5.12 Save Configuration 84
- 5-38: Reset Screen 85
- 6.1 Secured ini File 87
- 6.2 Modifying an ini File 87
- 6.3 The ini File Content 88
- 6.4 The ini File Structure 88
- 6.5 The ini File Example 89
- [NTP UTC Offset] 93
- 6.7 SNMP Parameters 98
- 6.12 Channel Parameters 128
- Version 4.4 129 July 2005 129
- Web Parameter Name 129
- Version 4.4 131 July 2005 131
- 7 Configuration Files 135
- 7.3 Voice Prompts File 137
- 8-1: Calling Name (Display) 139
- 8-2: Redirect Number 139
- 8.3 ISDN Overlap Dialing 140
- 8.4 Using ISDN NFAS 141
- 8.6.4 Relevant Parameters 147
- 8.7.2 Call Transfer 147
- 8.8 TDM Tunneling 149
- 8.9 Call Detail Report 151
- 8.11 SIP Call Flow Example 153
- 8.13.1 SIP2PRI Gateway 158
- 8.13.1.4 Transfer 161
- 8.13.3 DTMF Configuration 163
- 9 Diagnostics 165
- 9.2.1 Syslog Servers 166
- 9.2.2 Operation 166
- 10 BootP/DHCP Support 167
- 10.2 DHCP Support 169
- 10.3 BootP Support 169
- 11 SNMP-Based Management 171
- 11.1.2 SNMP MIB Objects 172
- 11.3 Cold Start Trap 173
- Measurements 174
- 11.6 SNMP Interface Details 177
- 11.6.2 Trusted Managers 178
- 11.6.3 SNMP Ports 179
- B.2 An Overview of BootP 189
- B.3 Key Features 189
- B.4 Specifications 190
- B.5 Installation 190
- Log Window 191
- B.9 Log Window 192
- B.10.1 BootP Preferences 193
- B.10.2 TFTP Preferences 194
- B.11.1 Adding Clients 195
- B.11.2 Deleting Clients 196
- B.11.4 Testing the Client 196
- B.11.6 on page 198 197
- Allocation 201
- D.1 Fax/Modem Settings 203
- Interface 207
- F.4 on page 209
- 6.2 on page 87 209
- 5.6 on page 41) 209
- 7.2 on page 137 215
- 6.1 on page 87 217
- G.2 PSTN Trace Utility 220
- H.6 Abort Procedure 225
- Appendix J SS7 Tunneling 231
- J.2 SS7 Characteristics 232
- J.3 SS7 Parameters 233
- J.4 SS7 Table Parameters 234
- J.4.2 SIGTRAN Interface IDs 235
- J.4.3 SS7 Signaling Link 236
- Version 4.4 239 July 2005 239
- J.6.1 Table Indices 242
- J.6.2 Table Permissions 242
- Card Application 245
- K.3 Supported Architecture 246
- K.4 Implementation 247
- K.4.2 Call Flow Description 248
- K.6 Configuration Parameters 249
- K.8 RADIUS Server Messages 253
- K.9 Voice XML Interpreter 254
- <disconnect> 256
- Version 4.4 257 July 2005 257
- Version 4.4 259 July 2005 259
- K.11.1 Voice Prompts 260
- K.11.2 VXML Flow Chart 262
- Version 4.4 263 July 2005 263
- Version 4.4 265 July 2005 265
- K.12 VXML Script Example 266
- Version 4.4 267 July 2005 267
- Version 4.4 269 July 2005 269
- Appendix L SNMP Traps 271
- L.1.4 Other Traps 276
- L.1.5 Trap Varbinds 276
- Declaration of Conformity 277
- Industry Canada Notice 278
- Digital Device Warnings 278
- FCC Statement 278
- Original 279
- CD or Web site 279
- AudioCodes Offices 280
Související produkty a manuály pro Hardware Nortel-networks Mediant TP-1610 SIP
Hardware Nortel-networks CG030601 Uživatelský manuál
(14 stránky)
(14 stránky)
Hardware Nortel-networks BSG12aw Uživatelský manuál
(66 stránky)
(66 stránky)
Hardware Nortel-networks 312865-A Uživatelský manuál
(18 stránky)
(18 stránky)
(2 stránky)
Hardware Nortel-networks NN43001-318 Uživatelský manuál
(108 stránky)
(108 stránky)
Hardware Nortel-networks Nortel Network VPN Router and Client Workstation 7 Uživatelský manuál
(67 stránky)
(67 stránky)
Hardware Nortel-networks CWDM SFP Uživatelský manuál
(34 stránky)
(34 stránky)
Hardware Nortel-networks NN46110-602 Uživatelský manuál
(230 stránky)
(230 stránky)
Hardware Nortel-networks 4134 Uživatelský manuál
(40 stránky)
(40 stránky)
Sony VPCJ218FG manuali
Manuali dei proprietari e guide per l'utente per no Sony VPCJ218FG.
We fornisce 1 manuali pdf Sony VPCJ218FG per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Komentáře k této Příručce