Nortel CallPilot600r Server HardwareInstallationNN44200-307.

10 Chapter 1 How to get helpGetting help from a specialist by using an Express Routing CodeTo access some Nortel Technical Solutions Centers, you can

11Chapter 2600r server descriptionIn this chapter"Conventions for Warnings" (page 11)"Server features" (page 12)"PCI riser as

12 Chapter 2 600r server descriptionCAUTIONAlerts you to situations where data can be lost or damaged,equipment can be damaged, actions can result in

Server features 13Clearance•front: 2 inches (50.8 mm)• rear: 3.6 inches (92 mm)•side: 1 inch (25 mm)Weight of fully loaded system with:•SCSI hard driv

14 Chapter 2 600r server descriptionFigure 1Front panelThe following diagram shows the front panel controls and status LEDs.For more information about

Server features 15Label Description Label DescriptionC Critical fault LED K System ID LED (white)D Major fault LED J NIC activity LED (green)E Minor f

16 Chapter 2 600r server descriptionLabel Description Label DescriptionD PCI card bracket(full-height) for MPB96J Video connectorE Power supply K COM1

Network connectivity 17Sample network setup: Meridian 1The Meridian 1 switch can be one of the following:•Option 11C or Option 11C Mini using fiber con

18 Chapter 2 600r server descriptionIn the previous diagram, the telephony LAN (TLAN) subnet providesIP connectivity between the CS 1000 system and th

Supported peripheral devices 19For information about how to identify the location of the network interfaceconnectors, see "Rear panel controls an

Document status: StandardDocument version: 01.03Document date: 14 May 2008Copyright © 2007-2008, Nortel NetworksAll Rights Reserved.Sourced in CanadaT

20 Chapter 2 600r server descriptionReference documentsFor a list of all CallPilot documents, see the following CallPilot CustomerDocumentation Map.No

21Chapter 3Preparing for installationIn this Chapter"Installation overview" (page 21)"Unpacking the 600r server" (page 23)"In

22 Chapter 3 Preparing for installationStepDescriptionCheck2Unpack the server and ensure you have all the items youneed (see "Unpacking the 600r

Unpacking the 600r server 23Unpacking the 600r serverIntroductionFollow this procedure to unpack the server and peripherals.WARNINGRisk of personal in

24 Chapter 3 Preparing for installationInspecting the interior of serverIntroductionTo inspect the interior of your 600r server, you must remove the s

Inspecting the interior of server 25What is next?Continue with the hardware installation, Chapter 4 "Installing the server andperipheral devices&

26 Chapter 3 Preparing for installationNortel CallPilot600r Server Hardware InstallationNN44200-307 01.03 Standard5.0 14 May 2008Copyright © 2007-2008

27Chapter 4Installing the server and peripheraldevicesIn this chapter"Installing the server" (page 27)"Connecting peripherals to the se

28 Chapter 4 Installing the server and peripheral devicesTo install the serverStep Action1Place the 600r server in its chosen location. If you are ins

Connecting peripherals to the server 29Figure 7Rear panelTable 4Rear panel connectorsLabel Description Label DescriptionA USB 0, USB 1, USB 2(labelled

RADISYS is a trademark of Radisys Corporation.SLR4, SLR5, and TANDBERG are trademarks of Tandberg Data ASA.SYBASE is a trademark of Sybase, Inc.TEAC i

30 Chapter 4 Installing the server and peripheral devicesTo connect the modem to the serverYou require a modem to support remote dial-up access to the

Connecting peripherals to the server 31WARNINGThe terminator is not a hot-plug device. If you replace theterminator, or if you add an external SCSI pe

32 Chapter 4 Installing the server and peripheral devices4Install the SCSI tape drive terminator to the back of the SCSI tapedrive, as shown in Figure

Connecting the server to the Nortel server subnet (optional) 33Note: The ELAN connector is labeled 2 on the rear panel of theserver. For the connector

34 Chapter 4 Installing the server and peripheral devicespower switch. Two MAC addresses are shown on the label. The CLANMAC address is the top MAC ad

Installing the Nortel software feature dongle 35Figure 9Dongle plugged in to serverTo install the software feature dongleStep Action1On the rear panel

36 Chapter 4 Installing the server and peripheral devicesFigure 10Dongle without feature keya. To open the dongle to insert the software feature key,

Installing the Nortel software feature dongle 374Plug the dongle in to USB port 0, the bottom USB connector, on therear panel of the server.Note: Due

38 Chapter 4 Installing the server and peripheral devicesNortel CallPilot600r Server Hardware InstallationNN44200-307 01.03 Standard5.0 14 May 2008Cop

39Chapter 5Connecting the server to powerIn this chapter"Safety precautions" (page 39)"Locating the power supply modules" (page 39

40 Chapter 5 Connecting the server to powerAC requirements as specified on the label of the power supply cover.To access the power supply cover, remove

Connecting the server to power 41A qualified electrician must implement the single-point ground reference asrequired among the power outlets of the Cal

42 Chapter 5 Connecting the server to powerFigure 13Example setup of 600r with peripheralsTo connect the 600r server to powerWARNINGRisk of personal i

Connecting the server to power 43Note: When the 600r server is plugged into an AC outlet with power,the server automatically powers on. If there is a

44 Chapter 5 Connecting the server to powerNortel CallPilot600r Server Hardware InstallationNN44200-307 01.03 Standard5.0 14 May 2008Copyright © 2007-

45Chapter 6EMC emission level protection for the600r serverTo lower the EMC emission level, ferrite cores are installed with one loop onthe following

46 Chapter 6 EMC emission level protection for the 600r serverFigure 14Ferrite cores secured to an external cableG101786FerritesConnectors for the MGa

47IndexSymbols/Numerics600r serverconnectionsestablishing 37power 37dimensions 12ELANconnection, establishing 32environmental specifications 13front pa

48 Indexreplacing 24front panel, description 13Kkeyboardconnecting to the server 29LLAN connections, description 18MMeridian 1, CallPilot server netwo

Index 49Wwarnings, conventions 11Nortel CallPilot600r Server Hardware InstallationNN44200-307 01.03 Standard5.0 14 May 2008Copyright © 2007-2008, Nort

5Publication HistoryMay 2008CallPilot 5.0, Standard 01.03 of the CallPilot 600r Server HardwareInstallation guide is issued for GA.May 2007CallPilot 5

50 IndexNortel CallPilot600r Server Hardware InstallationNN44200-307 01.03 Standard5.0 14 May 2008Copyright © 2007-2008, Nortel Networks.

Nortel CallPilot600r Server Hardware InstallationCopyright © 2007-2008, Nortel NetworksAll Rights Reserved.Publication: NN44200-307Document status: St

6 Publication HistoryNortel CallPilot600r Server Hardware InstallationNN44200-307 01.03 Standard5.0 14 May 2008Copyright © 2007-2008, Nortel Networks.

7ContentsChapter 1 How to get help 9Chapter 2 600r server description 11Conventions for Warnings 11Server features 12PCI riser assembly 16Network conn

8 ContentsNortel CallPilot600r Server Hardware InstallationNN44200-307 01.03 Standard5.0 14 May 2008Copyright © 2007-2008, Nortel Networks.

9Chapter 1How to get helpThis section explains how to get help for Nortel products and services.Getting help from the Nortel Web siteThe best way to g