Nortel Networks 10BASE-T Uživatelský manuál Strana 209
- Strana / 330
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Using the Console Interface
309985-C Rev 00
3-67
Monitor Unit/Port
Indicates the port number (of the specified unit) that is designated as the monitor
port.
Default Zero-length string
Range 1 to 8 / 1 to 28 (depending on model type)
Unit/Port X
Indicates one of the ports (of the specified unit) that will be monitored by the
designated port monitor when one of the port-based monitoring modes is selected.
This port will be monitored according to the value X in the Monitoring Mode field (see
Ta b l e 3 - 2 5
).
Default Zero-length string
Range 1 to 8 / 1 to 28 (depending on model type)
Unit/Port Y
Indicates one of the ports (of the specified unit) that will be monitored by the
designated port monitor when one of the port-based monitoring modes is selected.
When installed as a standalone switch, the screen does not display the (Unit/) field
designation. This port will be monitored according to the value Y in the Monitoring
Mode field (see Ta b l e 3 - 2 5
).
Default Zero-length string
Range 1 to 8 / 1 to 28 (depending on model type)
Address A
Indicates the MAC addresses that will be monitored by the designated port monitor
when one of the address-based monitoring modes is selected. This port will be
monitored according to the value “Address A” in the selected Monitoring Mode field
(see Ta bl e 3 - 25
). Users can enter the MAC address from this screen or from the MAC
Address Table screen. The entry is displayed and can be modified by either screen
(see “MAC Address Table” on page 3-21).
Default 00-00-00-00-00-00 (no MAC address assigned)
Range 00-00-00-00-00-00 to FF-FF-FF-FF-FF-FF
Address B
Indicates the MAC addresses that will be monitored by the designated port monitor
when one of the address-based monitoring modes is selected. This port will be
monitored according to the value “Address B” in the selected Monitoring Mode field
(see Ta bl e 3 - 25
). Users can enter the MAC address from this screen or from the MAC
Address Table screen. The entry is displayed and can be modified by either screen
(see “MAC Address Table
” on page 3-21).
Default 00-00-00-00-00-00 (no MAC address assigned)
Range 00-00-00-00-00-00 to FF-FF-FF-FF-FF-FF
Table 3-24. Port Mirroring Configuration Screen Fields
(continued)
Field Description
- Using the BayStack 410-24T 1
- 10BASE-T Switch 1
- Trademarks 2
- Statement of Conditions 2
- USA Requirements Only 2
- European Requirements Only 2
- Taiwan Requirements 3
- Canada Requirements Only 3
- Contents 7
- 309985-C Rev 00 10
- Audience 24
- Organization 24
- Text Conventions 25
- Acronyms 26
- Related Publications 28
- How to Get Help 29
- Chapter 1 31
- Front Panel 32
- 410-24T Switch 34
- Back Panel 36
- Features 39
- Security 43
- IEEE 802.1p 46
- IGMP Snooping Feature 47
- Flash Memory Storage 47
- Configuration Parameters 48
- MultiLink Trunking 49
- IEEE 802.1Q VLANs 49
- Port Mirroring 49
- SNMP MIB Support 51
- SNMP Trap Support 51
- Network Configuration 52
- Segment Switch Application 54
- CPU PS1 PS2FAN 55
- Fail-Safe Stack Application 56
- Stack Operation 57
- Cascade A Out 59
- Cascade A In 59
- Unit Select 59
- Cascade A InUnit Select 60
- Base Unit 61
- Stack Configurations 63
- IEEE 802.1Q VLAN Workgroups 68
- IEEE 802.1Q Tagging 69
- Shared Servers 76
- (Port Name is 80
- VLAN Workgroup Summary 81
- VLAN Configuration Rules 83
- IGMP Snooping 84
- IEEE 802.1p Prioritizing 89
- MultiLink Trunks 93
- Before Configuring Trunks 105
- 400-4FX MDA 107
- Chapter 2 119
- Figure 2-1. Package Contents 120
- Installation Procedure 121
- Caution: 122
- Comm Port 129
- Connecting Power 130
- Cascade Module 131
- 100-240V 131
- 47-63Hz~ 131
- Redundant Power 131
- Verifying the Installation 132
- Initial Setup 135
- Stack Setup 138
- Chapter 3 143
- Using the Console Interface 143
- Main Menu 146
- IP Configuration/Setup 150
- Choosing a BootP Request Mode 152
- BootP Disabled 153
- BootP or Last Address 153
- BootP When Needed 154
- BootP Always 154
- SNMP Configuration 155
- System Characteristics 157
- Switch Configuration 160
- MAC Address Table 163
- MAC Address-Based Security 165
- and 3-11) 170
- Configuration screen 171
- Screen 1 174
- Screen 2 174
- Screen 3 174
- Screen 4 174
- Screen 5 174
- Screen 16 178
- VLAN Configuration Menu 181
- Table 3-12 describes the 182
- Table 3-14 187
- Table 3-15. Reserved PIDs 188
- Port Configuration 195
- Table 3-19 describes the 196
- MultiLink Trunk Configuration 200
- Table 3-21 describes the 201
- Table 3-23 describes the 206
- Port Mirroring Configuration 207
- Table 3-24 describes the 208
- Table 3-25. Monitoring Modes 210
- Rate Limiting Configuration 211
- IGMP Configuration Menu 214
- Table 3-29 describes the 220
- Port Statistics 221
- ATM Configuration Menu 225
- Renumber Stack Units 243
- Hardware Unit Information 245
- Spanning Tree Configuration 245
- Software Download 256
- Download screen 257
- Configuration File 260
- Display Event Log 263
- Excessive Bad Entries 264
- Write Threshold 265
- Flash Update 265
- Save Current Settings 266
- Reset to Default Settings 269
- Chapter 4 273
- Troubleshooting 273
- Interpreting the LEDs 274
- Warning: 276
- Normal Power-Up Sequence 277
- Port Connection Problems 278
- Software Download Error Codes 280
- Appendix A 283
- Technical Specifications 283
- Physical Dimensions 284
- Performance Specifications 284
- Data Rate 285
- Interface Options 285
- Safety Agency Certification 285
- Electromagnetic Emissions 285
- Electromagnetic Immunity 286
- Declaration of Conformity 286
- Appendix B 287
- Media Dependent Adapters 287
- 400-4TX MDA 288
- 100BASE-FX MDAs 289
- 400-2FX MDA 290
- Installing an MDA 292
- Replacing an MDA 293
- Appendix C 295
- Quick Steps to Features 295
- Configuring 802.1Q VLANs 296
- Off-page reference 297
- On-page reference 297
- Configuring MultiLink Trunks 302
- Configuring Port Mirroring 303
- Configuring IGMP Snooping 305
- Appendix D 309
- MDI and MDI-X Devices 310
- Appendix E 315
- Default Settings 315
- Appendix F 323
Související produkty a manuály pro Sítě Nortel Networks 10BASE-T
Sítě Nortel Networks NN43001-321 Uživatelský manuál
(110 stránky)
(110 stránky)
Sítě Nortel Networks 24T Uživatelský manuál
(310 stránky)
(310 stránky)
Sítě Nortel Networks 400-S Uživatelský manuál
(86 stránky)
(86 stránky)
Sítě Nortel Networks 5100 Uživatelský manuál
(160 stránky)
(160 stránky)
Sítě Nortel Networks NN47200-503 Uživatelský manuál
(318 stránky)
(318 stránky)
Sítě Nortel Networks NN46110-602 Uživatelský manuál
(230 stránky)
(230 stránky)
Sítě Nortel Networks CVX 600 Uživatelský manuál
(168 stránky)
(168 stránky)
Sítě Nortel Networks 553-3901-200 Uživatelský manuál
(48 stránky)
(48 stránky)
Sítě Nortel Networks WEB OS 212777 Uživatelský manuál
(482 stránky)
(482 stránky)
Sítě Nortel Networks NN43001-301 Uživatelský manuál
(306 stránky)
(306 stránky)
Sítě Nortel Networks NN43001-314 Uživatelský manuál
(418 stránky)
(418 stránky)
Sítě Nortel Networks 553-3001-358 Uživatelský manuál
(244 stránky)
(244 stránky)
Sítě Nortel Networks NN44200-313 Uživatelský manuál
(66 stránky)
(66 stránky)
Sítě Nortel Networks HotWire 8600 Uživatelský manuál
(62 stránky)
(62 stránky)
Sítě Nortel Networks P0990474 Uživatelský manuál
(94 stránky)
(94 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.346 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce